TOA VM-2240 System Multi Functional Amplifier is a multi functional amplifier that can be mounted in an EIA-Standard equipment rack (3-unit size). The unit comes with 4 audio inputs including the background music input, and the speaker output section which has an internal attenuator and 5-zone selector. It permits not only general-purpose broadcast, but also Emergency Broadcast based on the EN60849 Standard
which gives pre-recorded voice instructions (optional EV-200M is required) in the emergency situation. Broadcast can be made from an optional RM-200M Remote Microphone as well as from the amplifier, and can be remotely controlled from external equipment. In addition, for 100 V application the unit features the surveillance function (optional SV-200MA is required) which automatically checks the system for failures.
Voice Alarm System
TOA VM-2240 System Multi Functional Amplifier
Availability:
Available on backorder
• Programmable system management amplifier
• 120 W or 240 W
• 5 switchable high impedance speaker zones with adjustable attenuators
• 9 units can be combined to increase the output power and number of zones
• 4 input channels come with volume and bass/ treble control on the front panel
• Both BGM inputs with level pre-adjustment
• The routing to the zones of the 3 microphone/ line level inputs and the telephone paging input can be pre-set
• Emergency power input, remote power control, 7 built-in chimes etc.
Compare
TOA VM-2240
Brand |
---|
Specifications
Power Source | AC: 120 V or 230 V, 50/60 Hz |
DC: 24 V/7.5 A (VM-2120), 24 V/15 A (VM-2240), M3.5 screw | |
terminal, Barrier distance: 8 mm, Applicable cable gauge: | |
AWG22 –AWG14 | |
Power Consumption on AC Mains | 54 W(With no signal present) |
Current Consumption on 24 V DC Power Input | 1 A(With no signal present) |
Frequency Response | 50 Hz – 16 kHz |
Distortion | 1% or less |
Signal-to-Noise Ratio | 60 dB or more |
Tone Control | Bass: 100 Hz ±10 dB, Treble: 10 kHz ±10 dB |
(Inputs 1 – 3 and BGM individually adjustable.) | |
Remote Microphone/Expansion Amplifier Connection | 2 RJ45 female connectors for connecting the RM-200M Remote |
Microphone and the VM-2120 or VM-2240 unit used as an expansion amplifier. | |
Maximum distance: 800 m in total | |
Link cable: Category 5 Shielded Twisted-P air straight | |
cable (TIA/EIA-568A standard) | |
Number of connectable RM-200M’s: Up to 4 | |
Input | Inputs 1 – 3:–60 dB*1 (MIC)/–10 dB*1 (LINE) (changeable), 600 Ω, electronically balanced*2, combined XLR connector (female)/phone jack (Only Input 1 is additionally equipped with DIN connector*3.) |
Telephone Paging Input: Push-in terminal block*4 | |
Voice sound: –10 dB*1, 10 kΩ, electronically-balanced input with shield terminal*2 | |
Control: No-voltage make contact input, open voltage: 3.3 V | |
DC, short-circuit current: under 1 mA | |
Control Input | For controlling Inputs 1 – 3, Push-in terminal block |
No-voltage make contact input, open voltage: 3.3 V DC, short-circuit | |
current: under 1 mA or less | |
Control Input and Output | D-sub connector (25-pin, female) |
Input: No-voltage make contact input, open voltage: 3.3 V DC,short-circuit current: 1 mA or less | |
Output: Open collector output, withstand voltage: 30 V DC, control | |
current: 10 mA or less | |
(1) External control input | |
Activation of messages*6 | |
Activation of power | |
Activation and stop of Emergency Broadcast | |
Unit’s broadcast cutoff (when activated by an external emergency equipment) | |
(2) Status output | |
Irregularity of communications with the Remote Microphone and an expansion amplifier | |
AC power condition | |
DC power condition | |
Irregularity of the sound source of the Voice Announcement Board | |
Failure (FAULT) indication on | |
Power switch on | |
External Attenuator Control Output | Plug-in screw connector*5, relay, no-voltage make contact output, |
transfer type, withstand voltage: 30 V DC, 125V AC, contact current: | |
7 A (DC) or less, 7 A (AC) or less | |
Surveillance Input and Output (*9) | D-sub connector (25-pin, female) |
Input: No-voltage make contact input, open voltage: 3.3 V DC, | |
short-circuit current: 1 mA or less | |
Output: Open collector output, withstand voltage: 30 V DC, | |
operating current: 10 mA or less | |
Power Supply | 24 V DC/0.1 A, for supplying power to an optional Amplifier Control Unit RU-2001/-2002, push-in terminal block* |
Chine Tone | Built-in chime: 2-tone chime/2-tone chime (fast repeat)/4-tone chime |
(Up)/Single-tone chime/ 4-tone chime (Up & Down)/off | |
Voice Announcement Board sound source: Pre-recorded chime*6 | |
Function | Two units stacking (VM-2120 or VM-2240) Emergencya broadcast (sequential control) Broadcast priority control |
Surveillance (failure detection) function Power supply to only one Remote Microphone (RM-200M) | |
Line resistance: 40 Ω (one way) or less | |
Operating Temperature | 0 – 40 °C |
Finish | Panel: ABS resin, dark gray (PANTONE 447C or its equivalent), paint |
Case: Steel plate, dark gray (PANTONE 446C or its equivalent), paint | |
Dimensions | 419 (w) x 143.3 (h) x 355.7 (d) mm |
Shad Chollack –
does the trick for a gym that wanted separate volumes in different areas. just enough power
Shad Chollack –
Khanz –
Sound quality is better than market speakers.
Khanz –
Nafisa –
Good Design and Build quality.
Nafisa –